We now accept the following payment options:

36 Item(s) Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. Next
Show per page
Samurai Inner Axle Seal
Samurai Inner Axle Seal
$6.30

Looking for just the inner axle seal by itself without purchasing the entire kit? We have them right here. Fits 1986-1995 Samurai.
Learn More


Samurai Rock Assault Rear Axle Housing
Samurai Rock Assault Rear Axle Housing
$400.00

Trail-Gear is proud to introduce "The Strongest Samurai Axle Housing Ever Made". The Samurai Rock Assault™ Axle Housing is a Toyota IFS width axle housing that is offset for a Samurai t-case. This housing features a heavy-duty, press formed, 1/4" plate steel center section shell that is specially shaped to ensure a minimum of 3/4" additional clearance under the differential. The differential mounting surface is made from 1/2” plate steel and comes with our Differential Stud Eliminator Kit to ensure that your differential never pulls out of the housing. The outer offset flanges are made from 4130 chromoly to prevent distortion or bending. Axle tubes are made from 1/4” thick DOM tubing, with a 3” outer diameter. This exclusive design features axle tubes that have been offset above the housing centerline. The inner axles ride near the bottom of the axle tubes rather than in the center. The results are an increase of 3/8" ground clearance under the axle tubing. The center section is offset to line up with the Samurai t-case so that your driveline does not vibrate from being offset. The Samurai Rock-Assault axle housings use stock or aftermarket 1986-1995 Toyota Pickup/4Runner brake backing plates and brake assemblies and uses a custom length chromoly axle shaft that Trail-Gear is also very proud to manufacture.. An optional fill/inspection cap can be installed for an additional fee. Overall housing length is 51 1/2 inches from mounting flange to mounting flange. Axle is shipped unpainted and lightly oiled to prevent rusting. We recommend degreasing housing inside and out before installation and painting.
Learn More


Samurai Rock Assault™ 33-Spline Birfields
Samurai Rock Assault™ 33-Spline Birfields
$169.00

With larger tires and more horse power than ever before being used on the trails these days, upgrades for your rig are more critical than ever.  In a Samurai, one of the more common failures are the stock birfields.  That is why we have developed our new Samurai Rock Assault™ 33-Spline chromoly birfields.  These birfields are made out of 4340 chromoly steel with 300M chromoly steel internal components. This birfield will get you to where you need to go and give you confidence and peace of mind while you are getting there.

**MADE IN THE USA**

Listed below are the testing results of our new Samurai Rock Assault™ 33-Spline Front Axle Kit in comparison to stock and our old Samurai Front Axle Kit.

Samurai Rock Assault™ 33-Spline Front Axle Kit Testing Results
  Stock Old TG Kit New TG 33-Spline Kit
Torque (ft-lbs) 2637 3684 4689

 

Samurai 33-Spline Front Axle Kit, 300750-3-KIT


Learn More


Samurai Rock Assault™ 33-Spline Front Axle Kit
Samurai Rock Assault™ 33-Spline Front Axle Kit
$399.00

Even though our Samurai customers loved our Samurai Rock Assault Front Axle Kit, they still asked for something even stronger. Our CEO challenged the engineering department to think of ways to make the Front Axle kit even stronger, so they put their heads together and came up with this new Samurai Rock Assault™ 33-Spline Front Axle Kit. The Samurai Rock Assault™ 33-Spline Front Axle shafts are made out of 4340 chromoly steel. The upgrades don’t just stop there. We also constructed the Birfield housing out of forged 4340 chromoly steel with 300M chromoly steel internal components. The shafts have a larger diameter than stock and are upgraded to 26-splines on the differential side. The Birfield side of the axle shaft and the inner race of the Birfield have been upgraded to 33-splines to better distribute the torque loading. **MADE IN THE USA** Kit Includes: Birfields Front axles C-clips Note: To install The Samurai Rock Assault™ 33-Spline Front Axle Kit you will need 26 spline spider gears in your 3rd member. You can obtain these 26 spline spider gears either by purchasing the OEM rear axle spider gears (they are 26 spline stock in the rear third) or by simply purchasing a locker with 26 spline spider gears, which is common in this application.
Learn More


Samurai Rock Assault™ Front Axle Shafts: long side (33-29 spline)
Samurai Rock Assault™ Front Axle Shafts: long side (33-29 spline)
$79.00

These axle shafts are the best of the best; manufactured from 4340 chromoly and consistently tested to a failure rate of around 4689ft/lbs.  The shafts have a larger diameter than stock and are upgraded to 26-splines on the differential side. The Birfield side of the axle shaft and the inner race of the Birfield have been upgraded to 33-splines to better distribute the torque loading.

**MADE IN THE USA**

Listed below are the testing results of our new Samurai Rock Assault™ 33-Spline Front Axle Kit in comparison to stock and our old Samurai Front Axle Kit.

Samurai Rock Assault™ 33-Spline Front Axle Kit Testing Results
  Stock Old TG Kit New TG 33-Spline Kit
Torque (ft-lbs) 2637 3684 4689

 

Available Options:

  • Samurai Rock Assault™ Front Axle Shaft, Short Side (33 to 26-Spline), 300751-3
  • Samurai Rock Assault™ Front Axle Shaft, Long Side (33 to 26-Spline), 300752-3

Learn More


Samurai Rock Assault™ Front Axle Shafts: short side (33-26 spline)
Samurai Rock Assault™ Front Axle Shafts: short side (33-26 spline)
$79.00

These axle shafts are the best of the best; manufactured from 4340 chromoly and consistently tested to a failure rate of around 4689ft/lbs.  The shafts have a larger diameter than stock and are upgraded to 26-splines on the differential side. The Birfield side of the axle shaft and the inner race of the Birfield have been upgraded to 33-splines to better distribute the torque loading.

**MADE IN THE USA**

Listed below are the testing results of our new Samurai Rock Assault™ 33-Spline Front Axle Kit in comparison to stock and our old Samurai Front Axle Kit.

Samurai Rock Assault™ 33-Spline Front Axle Kit Testing Results
  Stock Old TG Kit New TG 33-Spline Kit
Torque (ft-lbs) 2637 3684 4689

 

Available Options:

  • Samurai Rock Assault™ Front Axle Shaft, Short Side (33 to 26-Spline), 300751-3
  • Samurai Rock Assault™ Front Axle Shaft, Long Side (33 to 26-Spline), 300752-3

Learn More


Samurai Rock Assault™ Rear Axle Housing Kit
Samurai Rock Assault™ Rear Axle Housing Kit
$699.00

Trail-Gear is proud to introduce "The Strongest Samurai Axle Housing Ever Made". The Samurai Rock Assault™ Axle Housing Kit is a Toyota IFS width axle housing that is offset for a Samurai t-case. This housing features a heavy-duty, press formed, 1/4" plate steel center section shell that is specially shaped to ensure a minimum of 3/4" additional clearance under the differential. The differential mounting surface is made from 1/2” plate steel and comes with our Differential Stud Eliminator Kit to ensure that your differential never pulls out of the housing. The outer offset flanges are made from 4130 chromoly to prevent distortion or bending. Axle tubes are made from 1/4” thick DOM tubing, with a 3” outer diameter. This exclusive design features axle tubes that have been offset above the housing centerline. The inner axles ride near the bottom of the axle tubes rather than in the center. The results are an increase of 3/8" ground clearance under the axle tubing. The center section is offset to line up with the Samurai t-case so that your driveline does not vibrate from being offset. The Samurai Rock-Assault axle housings use stock or aftermarket 1986-1995 Toyota Pickup/4Runner brake backing plates and brake assemblies and uses a custom length chromoly axle shaft that Trail-Gear is also very proud to manufacture.. An optional fill/inspection cap can be installed for an additional fee. Overall housing length is 51 1/2 inches from mounting flange to mounting flange. Axle is shipped unpainted and lightly oiled to prevent rusting. We recommend degreasing housing inside and out before installation and painting. This housing uses a Toyota 8" differential. Kit Includes: Samurai Rock Assault™ Rear Axle Housing Chromoly Samurai axles Differential stud eliminator kit Differential drain plug Ultra grey silicone
Learn More


Samurai Rock Assault™ Rear Axle Housing Kit with E-Locker
Samurai Rock Assault™ Rear Axle Housing Kit with E-Locker
$699.00

Trail-Gear is proud to introduce "The Strongest Samurai Axle Housing Ever Made". The Samurai Rock Assault™ Axle Housing Kit is a Toyota IFS width axle housing that is offset for a Samurai t-case. This housing features a heavy-duty, press formed, 1/4" plate steel center section shell that is specially shaped to ensure a minimum of 3/4" additional clearance under the differential. The differential mounting surface is made from 1/2” plate steel and comes with our Differential Stud Eliminator Kit to ensure that your differential never pulls out of the housing. The outer offset flanges are made from 4130 chromoly to prevent distortion or bending. Axle tubes are made from 1/4” thick DOM tubing, with a 3” outer diameter. This exclusive design features axle tubes that have been offset above the housing centerline. The inner axles ride near the bottom of the axle tubes rather than in the center. The results are an increase of 3/8" ground clearance under the axle tubing. The center section is offset to line up with the Samurai t-case so that your driveline does not vibrate from being offset. The Samurai Rock-Assault axle housings use stock or aftermarket 1986-1995 Toyota Pickup/4Runner brake backing plates and brake assemblies and uses a custom length chromoly axle shaft that Trail-Gear is also very proud to manufacture.. An optional fill/inspection cap can be installed for an additional fee. Overall housing length is 51 1/2 inches from mounting flange to mounting flange. Axle is shipped unpainted and lightly oiled to prevent rusting. We recommend degreasing housing inside and out before installation and painting. This housing uses a Toyota 8" differential. Kit Includes: Samurai Rock Assault™ Rear Axle Housing Chromoly Samurai axles Differential stud eliminator kit Differential drain plug Ultra grey silicone
Learn More


Samurai Rock Assault™ Rear Axle Housing with E-Locker
Samurai Rock Assault™ Rear Axle Housing with E-Locker
$400.00

Trail-Gear is proud to introduce "The Strongest Samurai Axle Housing Ever Made". The Samurai Rock Assault™ Axle Housing is a Toyota IFS width axle housing that is offset for a Samurai t-case. This housing features a heavy-duty, press formed, 1/4" plate steel center section shell that is specially shaped to ensure a minimum of 3/4" additional clearance under the differential. The differential mounting surface is made from 1/2” plate steel and comes with our Differential Stud Eliminator Kit to ensure that your differential never pulls out of the housing. The outer offset flanges are made from 4130 chromoly to prevent distortion or bending. Axle tubes are made from 1/4” thick DOM tubing, with a 3” outer diameter. This exclusive design features axle tubes that have been offset above the housing centerline. The inner axles ride near the bottom of the axle tubes rather than in the center. The results are an increase of 3/8" ground clearance under the axle tubing. The center section is offset to line up with the Samurai t-case so that your driveline does not vibrate from being offset. The Samurai Rock-Assault axle housings use stock or aftermarket 1986-1995 Toyota Pickup/4Runner brake backing plates and brake assemblies and uses a custom length chromoly axle shaft that Trail-Gear is also very proud to manufacture.. An optional fill/inspection cap can be installed for an additional fee. Overall housing length is 51 1/2 inches from mounting flange to mounting flange. Axle is shipped unpainted and lightly oiled to prevent rusting. We recommend degreasing housing inside and out before installation and painting.
Learn More


Samurai Spindle Nut Kit
Samurai Spindle Nut Kit
$7.35

Normally the nuts that hold the wheel bearings can be reused over and over again. If your wheel bearing retainer nuts need replacing this kit is for you. Kit contains 2 nuts, star washer and flat index washer.
Learn More


36 Item(s) Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. Next
Show per page